Відео

I still hate those print lines

Very nicely done, Sir. Bravo!

Fantastic airbrushing. For the "glass" cover on the dashboard instruments, try first putting a small drop of clear acrylic in the center of the dial without letting it touch the edges. After letting it dry a little, slowly fill in the rest of the area with the clear until it touches the edge of the dial. It should make for a smoother surface and reduce or eliminate the meniscus forming in the clear paint if applied all at once. For metal surfaces like the rear view mirror, try applying VMS steel metallic pigment (No. 25) to the silver painted area and burnishing it down to a shinny metallic finish. Thanks for a great build and video.

James mate, truly incredible! Massive respect for that figure, and I also really like the fact that the bike looks dirty and weathered, but that the weathering is in-scale. It's super easy to go overboard but you've got it just right with this!

Wow. Dude you’re just getting better and better. You should be proud 👊🏻

I have loved this build so much that I have ended up ordering the same kit from CSM. Your build will be the benchmark for to aspire for.

Nice job! But the printing layers are still quite visible - It's the only disadvantage of this model. The same problem with CSM Tiger Model H bike I built recently. That's why I doubt about purchasing their next bikes (but their planes and armoured cars are beautiful!).

Genial Die detaillierte Bemalung des Kopfes und des gesamten Modells, in dieser Größe, ist unglaublich. 👊😎👍

Superb job, congratulations!

Very nice work mate

I think it looks amazing

The raw model is pretty amazing

Best Job Master !!!!!🏆

Brought that detail out nicely, stunning little model, really well done! 👍🇬🇧

These 'steps' from 3D printing are really visible. Shame CSM didn't manage to avoid them, because they charge a small fortune for this kit. Anyway and little bit of attention to details would be great move from their side. Same like in their platic models they omit some details tso later then can charge fortune for their' replacements'. Money is more interesting than customer satisfaction.

Greet bill. Really like the die Rama. You like the painting of the figure top-notch?Can't wait to see your next video

Just wow...nuff said.!!!!

Lovely model and great job 👍🏻

Lovely.

I have this printer, and even at 50 micron layer height I’m blown away with the print quality. The AI camera is a gimmick to me. I’ve had prints where half the bed failed and I was never notified of any failure. It also kind of sucks that there isn’t a mobile app for this printer, like the Bambu printers have- I’d like to be able to get notifications and check in on my prints from my phone. Overall, it’s a great printer though!

Fantastic job on the kit! I am building the Copper State standing RNAS pilot currently and the detail is impressive on it as well.

I think you did an amazing job. I would put you amongst the best figure painters I watch on You Tube. I am ok with the clothes but my face painting leaves a lot to be desired, but I think I need to focus on the better moulded figures.

Very nice James, the kit and figure look amazing.

Hi James, you mentioned at the start, thst you hoped you could do this build justice, well I can tell you, you certainly have donebthe kit great justice, congratulations on a job very well done, best regards from a Kiwi living in Australia, Les

incredible work

Great build!

Wow, that must have been a satisfying build. Awesome result. Very enjoyable to watch 💥👋💥

I really enjoyed the music on this video.

Excellent work really enjoyed the build plus the face painting 👍

thats awesome very nice work indeed ! I need to ask Edgar to send me that kit is great ,as i told them before they need to make an 1/16 scale will be a killer kit !By the way a small tip because you have already uv resin to your hands ,when you want to remove some of the layer lines you can brush some of it especially if it is a flat surface ,cure it and you are done ! Works for me anyway and makes those layers less pronounced !

Amazing work mate! The figure colour balance is phenomenal, you've blended everything really well. What thinning ratio did you use for his face layers? Looking forward to your next video

you did a awesome job paying tribute to an excellent kit ! well done

Really rather good mate 😉👌

can we see you build a locomotive from dapol

very nice and such an accuratley sculpted bike and figure to boot. excellent paint work has brought this to life.✌👍👍👍👍

Superb subject and craftmanship. Loved the video and the classical "theme" music with plenty of nostalgia. Given all these elements, this is one the best modelling videos I've seen in a while, well done and thank you!

That figure is fantastic. Try as I might I still can't quite crack them like that yet. Really nice subject with the early motorcycle too. Funny to see it has both manual pedals and a drive belt.

Absolute work of art, you have skills of note!!

Stunning dude!! Tottaly looks like Matt from Model minutes 😂

I would be afraid of breaking the fine parts just touching the model, lol. Awesome print!

I don't know if this is your best, but this one is absolutely stunning!

Beautiful. Very nicely done.

Awesome ❤ you got some silky skills there mate👌

Outstanding James!! That's wizardry mate. Thanks for sharing.

What a great build. The detail on the 3D bike is incredible but unfortunately I cannot unsee the print layer lines.😇

What a fantastic build and paint job well done I wish I had half the skill level to do that

Really cool weathering.

Painting eyes on a 1/35 figure is not easy to do. You did really nice work with this kit. Very enjoyable.

Very nice🎉

Great job, just beautiful!